Welcome to www.aakindustry.com

More Than 10 Manufacturers unable to avoid Iron Filings in Hydraulic Valve Block, But AAK Mass Produced It a Year Ago

Views : 217
Update time : 2021-10-15 10:40:47
Maarten purchased a batch of hydraulic valve blocks some time ago. In the early test, the system parameters were normal. Strangely, 10 days after the hydraulic valve block was started, the hydraulic oil in the system suddenly deteriorated. The technician immediately suspended the operation of the whole test system. After inspection, it was found that there were small iron filings in the hydraulic oil, and the valve spool of the cartridge valve connected with the hydraulic valve block also showed signs of wear. Maarten mentioned these problems to the hydraulic valve manufacturer, but the hydraulic manufacturer asked the customer to use better hydraulic oil and avoided the problem of his own hydraulic valve block. With delivery date approaching, Maarten is very helpless.
 
Maarten really had no choice but to try to find other suitable hydraulic valve manufacturers on the website to take over the hydraulic valve block order. He consulted no less than 10 manufacturers in a week, but all manufacturers gave the same reply, they could not 100% avoid fine iron filings. This made Maarten start to doubt the ability of the hydraulic valve manufacturers in China.
 
Before, Maarten had a certain understanding about us AAK hydraulic valve through some B2B websites, so with a try mentality, he directly emailed us a trial order for 5 hydraulic valve blocks. After receiving our hydraulic valve blocks, Maarten tested and compared, he found that AAK hydraulic valve block has strong sealing, high precision and gloss finish. What's more, he was glad that there was no iron filings residue. He immediately sent the drawings, quantity, delivery date and other detailed requirements of the hydraulic valve blocks currently being purchased from the other hydraulic valve manufacturer. After confirming all details with us, he cancelled the order with the original hydraulic valve manufacturer. At this moment, Maarten could finally rest assured.
 
Why do more than 10 hydraulic valve manufacturers dare not accept the order of this hydraulic valve block? Because this hydraulic valve block is very special. There are many slender holes in the processing channels intersected by each hydraulic valve block, and the cleaning of iron filings is a cumbersome process. If there is no unique skill, it is difficult to eradicate it 100%. 2 years ago, AAK hydraulic valve also had an order cancelled by customer due to the iron filings of hydraulic valve block not completely eradicated. After that lesson, our technical team spent half a year innovating the production process of hydraulic valve block, and finally AAK hydraulic valve was able to mass produce the hydraulic valve without iron filings 1 year ago.
 
The reason why AAK hydraulic valve block can remove the residual iron filings that can not be achieved by peers is that after the hydraulic valve block is processed, AAK firstly uses high-temperature alkaline water to cook the hydraulic valve block, so that the iron filings of the hydraulic valve block lose demagnetization, and then uses a small pneumatic grinding wheel to clamp the rotary file to go through the hole, so as to completely eliminate possible flash at the corner. Then, the high-pressure washing machine shall carry out high-pressure washing on the dirt on the inner and outer surfaces of the duct. Finally, the industrial endoscope and cold light source shall be used to check the flash and burr at the corner in the duct. If any, point-to-point and high-pressure washing shall be carried out until the iron filings in the hydraulic valve block are completely eradicated.
 
AAK hydraulic valve block is made with ingenuity. Don't worry about buying and using. You can also try a small order.
 
AAK Hydraulic Valve (85) 2021-10-15

 
Related News
Read More >>
Many Manufacturers can not produce the Hydraulic Cartridge Pressure Control Valve with 2μm Cylindricity, AAK produced in batch 3 years ago Many Manufacturers can not produce the Hydraulic Cartridge Pressure Control Valve with 2μm Cylindricity, AAK produced in batch 3 years ago
Dec .02.2022
Brishen is from Brazil. He has been purchasing hydraulic valves for 4 years smoothly, but was stumped by a hydraulic cartridge pressure control valve recently.
AAK 3 Skills Solved the problem of Hydraulic Counterbalance Cartridge Valve Caused by Back Pressure and helped Dorian's Equipment Promoted Smoothly AAK 3 Skills Solved the problem of Hydraulic Counterbalance Cartridge Valve Caused by Back Pressure and helped Dorian's Equipment Promoted Smoothly
Dec .01.2022
Dorian is from a Greek hydraulic equipment company and is responsible for the procurement of hydraulic components. At the beginning of the year, they developed a new hydraulic crane, which requires the use of hydraulic counterbalance cartridge valve.
For instantaneous unloading flow 10000lpm Hydraulic Cartridge Pressure Control Valve, Vadim only found AAK For instantaneous unloading flow 10000lpm Hydraulic Cartridge Pressure Control Valve, Vadim only found AAK
Nov .30.2022
Vadim is from the Netherlands and has been engaged in procurement in a hydraulic equipment company for 3 years. Some time ago, they encountered a complaint about the hydraulic support they sold.
For an Aluminum Hydraulic Manifold Block with 80 Deep Holes and 5mm wall thickness, AAK got the order for 300 pcs qty after the first samples For an Aluminum Hydraulic Manifold Block with 80 Deep Holes and 5mm wall thickness, AAK got the order for 300 pcs qty after the first samples
Nov .29.2022
For a 6061-T6 aluminum hydraulic manifold block with 80 deep cavities and a wall thickness of 5MM, Brody asked 3 hydraulic manifold block manufacturers to make samples, but they all failed.